Ethernet Remote IO Module M150T


Ethernet Remote IO Module M150T (8DIN+4AIN+4DO,High speed pulse counter,pulse output) adalah antarmuka RS485, melalui bus RS485, dapat mengalirkan perangkat Modbus RTU I / O atau pengukur Modbus RTU, misalnya: berbagai input digital atau output digital, input atau output analog, kombinasi modul IO resistansi termal, menghemat biaya. Pada saat yang sama, modul I / O Jarak Jauh Ethernet memiliki fungsi pemetaan register, data Modbus RTU I / O kaskade secara otomatis dikumpulkan ke area memori pemetaan, permintaan Klien Modbus TCP tanpa menunggu kemudian bisa mendapatkan respons cepat untuk memenuhi persyaratan tepat waktu industri.

Rp3,490,000

Ethernet Remote IO Module M150T (8DIN+4AIN+4DO,High speed pulse counter,pulse output) adalah antarmuka RS485, melalui bus RS485, dapat mengalirkan perangkat Modbus RTU I / O atau pengukur Modbus RTU, misalnya: berbagai input digital atau output digital, input atau output analog, kombinasi modul IO resistansi termal, menghemat biaya. Pada saat yang sama, modul I / O Jarak Jauh Ethernet memiliki fungsi pemetaan register, data Modbus RTU I / O kaskade secara otomatis dikumpulkan ke area memori pemetaan, permintaan Klien Modbus TCP tanpa menunggu kemudian bisa mendapatkan respons cepat untuk memenuhi persyaratan tepat waktu industri.

Spesification :
Ethernet Remote I/O Module Specifications

Digital Input
Sensor Type : Wet Contact (NPN or PNP), Dry Contact
I/O Mode : DI or Event Counter
Dry Contact : On: short to GND=0 ;Off: open=1
Wet Contact (DI to COM) : On: 10 to 30 VDC =1;Off: 0 to 3 VDC=0
Counter Frequency : 700khz(Only the 1st Channel can be used as high speed pulse counter)
Digital sampling frequency : 500Hz
Digital filtering strategy : Continues 3 times
Isolation : Optical Isolated,3k VDC or 2k Vrms

Digital Output
Type : Sink
I/O Mode : DO
Pulse Output Frequency : 10Hz~300KHz(Only the 1st Channel can be used as high speed pulse outputs)
Over-Voltage Protection : 50 VDC
Over-Temperature Shutdown : 175°C (typical), 150°C (min.)
Load Current : Max. 500 mA per channel
Digital sampling frequency : 500Hz

Analog Input
Type : Differential input
Resolution : 12 bits
I/O Mode : Voltage / Current (jumper selectable)
Input Range : 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA
Accuracy :±0.1% FSR @ 25°C
Sampling frequency : 20Hz
Built-in Resistor for Current Input : 162 ohms
Isolation : Electrical isolation

Working Power Requirements
Input Voltage : 12 to 36 VDC, Peak Voltage:+40VDC, Power consumption: Less than 3W;
Input Current : 139 mA @ 24 VDC

Power Output
Output Voltage : 12 to 36 VDC
Output Current : 139 mA @ 24 VDC

LAN
Ethernet : 10/100 Mbps, RJ45 ports
Protection : 15KV ESD Protection
Protocols : Modbus TCP, TCP/IP,TCP Server,TCP Client
Max. TCP Connection : 5

Serial Port
RS485 : MODBUS- RTU Protocol, Modbus-ASCII Protocol, Modbus Master or slave.
Protection : 15KV ESD Protection
Modbus Slave address : 1~255
Baud Rate : 1200,2400,4800,9600,19200,38400,57600,115200,128000Bps;
Mapping registers : Bit Type: 300 Registers, 16-Bit Type: 300 Registers.

Physical Characteristics
Wiring : I/O cable max. 14 AWG
Dimensions : 105 x 88 x 30 mm
Weight : Under 205 g
Mounting : DIN rail or wall

Environmental Limits
Operating Temperature : Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature : -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity :5 to 95% (non-condensing)
Altitude : Up to 3000 m

Weight 1000 kg

Ethernet Remote I/O Module Specifications

Digital Input
Sensor Type : Wet Contact (NPN or PNP), Dry Contact
I/O Mode : DI or Event Counter
Dry Contact : On: short to GND=0 ;Off: open=1
Wet Contact (DI to COM) : On: 10 to 30 VDC =1;Off: 0 to 3 VDC=0
Counter Frequency : 700khz(Only the 1st Channel can be used as high speed pulse counter)
Digital sampling frequency : 500Hz
Digital filtering strategy : Continues 3 times
Isolation : Optical Isolated,3k VDC or 2k Vrms

Digital Output
Type : Sink
I/O Mode : DO
Pulse Output Frequency : 10Hz~300KHz(Only the 1st Channel can be used as high speed pulse outputs)
Over-Voltage Protection : 50 VDC
Over-Temperature Shutdown : 175°C (typical), 150°C (min.)
Load Current : Max. 500 mA per channel
Digital sampling frequency : 500Hz

Analog Input
Type : Differential input
Resolution : 12 bits
I/O Mode : Voltage / Current (jumper selectable)
Input Range : 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA
Accuracy :±0.1% FSR @ 25°C
Sampling frequency : 20Hz
Built-in Resistor for Current Input : 162 ohms
Isolation : Electrical isolation

Working Power Requirements
Input Voltage : 12 to 36 VDC, Peak Voltage:+40VDC, Power consumption: Less than 3W;
Input Current : 139 mA @ 24 VDC

Power Output
Output Voltage : 12 to 36 VDC
Output Current : 139 mA @ 24 VDC

LAN
Ethernet : 10/100 Mbps, RJ45 ports
Protection : 15KV ESD Protection
Protocols : Modbus TCP, TCP/IP,TCP Server,TCP Client
Max. TCP Connection : 5

Serial Port
RS485 : MODBUS- RTU Protocol, Modbus-ASCII Protocol, Modbus Master or slave.
Protection : 15KV ESD Protection
Modbus Slave address : 1~255
Baud Rate : 1200,2400,4800,9600,19200,38400,57600,115200,128000Bps;
Mapping registers : Bit Type: 300 Registers, 16-Bit Type: 300 Registers.

Physical Characteristics
Wiring : I/O cable max. 14 AWG
Dimensions : 105 x 88 x 30 mm
Weight : Under 205 g
Mounting : DIN rail or wall

Environmental Limits
Operating Temperature : Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature : -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity :5 to 95% (non-condensing)
Altitude : Up to 3000 m

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Ethernet Remote IO Module M150T”

This site uses Akismet to reduce spam. Learn how your comment data is processed.

There are no reviews yet.

Open chat